What is an automatic watch?
Most of our watches use an automatic (self-winding) movement such as the NH35. There's no battery. Inside is a weighted rotor that spins as you move your wrist, winding a spring that powers the watch.
- It winds itself while you wear it. Normal daily wear keeps it running.
- It will stop if you don't wear it. A fully wound NH35 runs about 41 hours off the wrist. If it stops, that's normal. Just wind it and reset the time.
- The seconds hand sweeps instead of ticking once per second.
- Small daily drift is normal. Mechanical watches typically gain or lose a few seconds a day, more or less depending on how you wear it. That's part of owning one.
First time: wind it up
- Unscrew the crown (if needed). Many of our watches have a screw-down crown. Turn it toward you (counterclockwise) until it pops out to the winding position.
- Wind it. With the crown in this first, pushed-in position, turn it away from you (clockwise) about 20–30 times. You'll see the seconds hand start moving.
- Now set the time and date (below), then push the crown back in and screw it down snug. Don't force it.
Crown positions
- Position 0 (pushed in): wind the watch.
- Position 1 (first click out): set the date (and day, or GMT hand, on some models).
- Position 2 (all the way out): set the time. The seconds hand stops ("hacks") so you can sync it exactly.
Setting the time and date
- Pull the crown to position 2 and move the hands to 6:00. This keeps the date mechanism out of the way.
- Push to position 1 and turn the crown to set yesterday's date.
- Pull back to position 2 and move the hands forward until the date changes. That's midnight. Keep going to the correct time, so you know it's set to AM or PM correctly.
- Push the crown in and screw it down.
Important: don't change the date between about 9 PM and 3 AM on the watch. That's when the date gears are working and forcing them can damage the movement. Setting the hands to 6:00 first (step 1) avoids this.
Day-date models
On watches showing both day and date, in position 1 turning the crown one direction changes the date and the other direction changes the day. Use the same 6:00 rule above.
GMT models (NH34)
The fourth hand (24-hour GMT hand) shows a second time zone. In position 1, turning the crown one direction moves the date and the other direction moves the GMT hand in one-hour jumps. Set the main time in position 2 as normal.
Chronograph models (VK63)
Our chronographs use the VK63 meca-quartz movement: battery powered with quartz accuracy, plus a mechanical-feel stopwatch with a smooth sweeping hand.
- Top pusher: start and stop the stopwatch.
- Bottom pusher: reset to zero (when stopped).
- Set the time in position 2 and the date in position 1, just like above.
- The battery typically lasts a few years. Any watch shop can replace it.
- If the stopwatch hand doesn't return exactly to 12 after a battery change, email us and we'll walk you through re-zeroing it.
Water resistance
Each listing shows the water resistance. Many of our watches are 3 ATM (splash resistant): fine for rain and hand-washing, but not for showering or swimming. Always make sure a screw-down crown is fully screwed in before it gets wet.
Everyday care
- Wipe the case and bracelet with a soft cloth; a soft toothbrush and mild soapy water cleans the bracelet (keep the crown closed).
- Keep it away from strong magnets (speakers, magnetic phone mounts), which can make a mechanical watch run fast.
- Avoid hard knocks, like sports where the wrist takes impact.
- Not wearing it for a while? It's fine to let it stop. A watch winder is optional, not required.
Bracelet sizing
Need links removed? Any local jeweler or watch shop can do it in a few minutes, or email us your wrist size before your watch ships and we'll do our best to size it for you.
Returns
Every order comes with 30-day returns on unworn watches. See our full return policy for details.